RGH xbox not booting stock nand

[abyss]

today i installed my demon and updated the xbox to the newest dashboard. and tweaked it until i got pretty good boot timings for a falcon.

but now my stock nand refuses to boot. i just get a black screen the rol doesn't show anything eccept the green center light.

what could be the problem here?
if oyu need any pictures please tell me.

greetings,
abyss

 

[Mack702]

Is your stock nand and demon nand on the same dashboard?

 

[abyss]

yep same dash why?

 

[abyss]

and now its boots the stock nand but it refuses to glitch now..
well the cr doesn't give a green light anymore..

is my demon dead or faulty?

 

[Martin C]

we need pics and logs please.

 

[abyss]

j-runner logs? and will make pics now

but when i set it to glitch i can hear the fans 'reset' but no green light

---------- Post added at 12:59 ---------- Previous post was at 12:51 ----------

donderdag 13 september 2012 0:25:29

J-Runner v0.2 Beta (282) Started



Programming Coolrunner
C:\Users\Robin\Desktop\J-Runner v02\common\xsvf\falconrgh2.xsvf
sending xsvf to demon...
Done

===================================================
donderdag 13 september 2012 1:18:53

J-Runner v0.2 Beta (282) Started



Checking Files
Finished Checking Files
Version: 03

Flash Config: 0x01198010
Falcon/Opus
Reading Nand to C:\Users\Robin\Desktop\J-Runner v02\output\nanddump1.bin
Reading Nand
Done!
in 2:01 min:sec

Reading Nand to C:\Users\Robin\Desktop\J-Runner v02\output\nanddump2.bin
Initializing Nand..
Nand Initialization Finished
Reading Nand
Done!
in 2:01 min:sec

Comparing...
Nands are the same
Checking for bad blocks...
Done
Load Files Initiliazation Finished
15574
Started Creation of the 15574 xebuild image
KV Info saved to file
---------------------------------------------------------------
xeBuild v1.04.535
---------------------------------------------------------------
building glitch2 image
---------------------------------------------------------------
C:\Users\Robin\Desktop\J-Runner v02\067776282705\updflash.bin image built, info:
---------------------------------------------------------------
Console : Falcon
NAND size : 16MiB
Build : Glitch (v2)
Xell : power on console with console eject button
'removed cpu key etc'
CF LDV : 11
KV type : type2 (hashed)
---------------------------------------------------------------
xeBuild Finished. Have a nice day.
---------------------------------------------------------------

Saved to C:\Users\Robin\Desktop\J-Runner v02\067776282705
Image is Ready
DEMON
Hardware : Demon Phat
Firmware : 1.0
Flash ID : 0x73AD Hynix (16MiB - Small block)
Flash Size : 0x400 blocks of 0x4200 bytes
Writing Nand
Done!
in 0:30 min:sec

 

[Martin C]

I've just seen there in the logs that it's possibly a J-R bug . falconrgh2.xsvf is (AFAIK) not used for DemoN purposes.

Program the Coolrunner with Timing B and DemoN checked. See if the CR at least flashes with that.

I'm assuming you have the CR EN wire soldered from the Coolrunner to DemoN connector?

 

[abyss]

i have flashed the B timing file to the colrunner now but still no green light.
but i can hear the fans reset themselves?

yes CR_EN pad is soldered to the demon addon board

but i am wondering what purpose the orange and brown wire have

photo's are on their way btw.

 

[XL3THAL VIP3RX]

i have flashed the B timing file to the colrunner now but still no green light.
but i can hear the fans reset themselves?

yes CR_EN pad is soldered to the demon addon board

but i am wondering what purpose the orange and brown wire have

photo's are on their way btw.

the orange and brown wire are so you can switch nands using the sync button on the xbox

 

[abyss]

so if they aren't installed it shouldn't be a problem?

 

[Martin C]

Correct - you don't need them.

So I understand this, is your 360 NAND booting to stock ok? If so, we'll need pics of your CR soldering.

 

[abyss]

yes now is my xbox 360 nand booting fine.
will upload the pictures from the CR wiring.

pictures uploaded

 

[big_ted]

Can't tell from the pics you are using rgh2 after the update?

Ted

 

[abyss]

yep the wiring is for rgh 2

edit: but i don't understand why it would be the wiring because it glitched fine when the stock nand wasn't working..

 

[abyss]

nobody that know how to fix it?

 

[Martin C]

Check the soldering for STBY_CLK, just in case.

 

[abyss]

resoldered it just in case but still no green light on the CR.
it's like the demon isn't allowing the CR to glitch

 

[Martin C]

Post your log from flashing the CR please.

 

[abyss]

===================================================
donderdag 13 september 2012 14:13:19

J-Runner v0.2 Beta (282) Started
Checking Files
Finished Checking Files
Programming Coolrunner
C:\Users\Robin\Desktop\J-Runner v02\common\xsvf\RGH2_B_en.xsvf
sending xsvf to demon...
Done

 

[abyss]

it's still not working =(