Xbox slime will not write ECC

[vloxter]

I have a xbox slim I got from a friend and I thought it was a corono to find out it was a trinity. I tried to install a coolrunner rev.c and when I got done the xbox would not write the ECC. I then tried to tun it on it did but red light so I decided to re solder everything and now it just has the sounds but my points are clean as to my eyes. This has happened to my other xbox where I read the nand did all the stuff and wouldnt rite the ECC.
pictures:



These are all the pictures

and when i write the ECC it just goes through it as if all blocks are bad thanks

 

[GeekHeat]

Fill out the template with good CLEAR pics of soldering and coolrunner.
http://team-xecuter.com/forums/showthread.php?96474-TEMPLATE-RGH-JTAG-help

 

[GeekHeat]

I have a xbox slim I got from a friend and I thought it was a corono to find out it was a trinity. I tried to install a coolrunner rev.c and when I got done the xbox would not write the ECC. I then tried to tun it on it did but red light so I decided to re solder everything and now it just has the sounds but my points are clean as to my eyes. This has happened to my other xbox where I read the nand did all the stuff and wouldnt rite the ECC.
pictures:
View attachment 31698
View attachment 31699View attachment 31700View attachment 31701

These are all the pictures

and when i write the ECC it just goes through it as if all blocks are bad thanks

Nevermind. I can see you have a fake coolrunner rev D. Which we don't support on here.

 

[vloxter]

Nevermind. I can see you have a fake coolrunner rev D. Which we don't support on here.

I have a real one and can show proof I was testing the fakes to see if they work and they do work but it wouldnt work on this console the real one and i decided to ty the fake one since it worked on my last one but yeah I tired both.

 

[GeekHeat]

I have a real one and can show proof I was testing the fakes to see if they work and they do work but it wouldnt work on this console the real one and i decided to ty the fake one since it worked on my last one but yeah I tired both.

U still need to fill out the template with good clear pics of your soldering and genuine coolrunner.

 

[Brickmii82]

You do realize that cheap Chinese electronic knockoffs (any and all) are responsible for numerous failures(best case scenario) and possibly fires (worst case scenario). Plus they ride off the backs of the genuine manufacturers of the product causing prices for the genuines to go up to make up for the revenue "lost" to these fake pos replicas. Why even try it? For a few more dollars you get a guaranteed proven product.

On a side note, this "I used a clone and.." crap is really annoying. Whether it worked or not, you're putting cost before quality control and that's piss poor ethics.

 

[vloxter]

You do realize that cheap Chinese electronic knockoffs (any and all) are responsible for numerous failures(best case scenario) and possibly fires (worst case scenario). Plus they ride off the backs of the genuine manufacturers of the product causing prices for the genuines to go up to make up for the revenue "lost" to these fake pos replicas. Why even try it? For a few more dollars you get a guaranteed proven product.

On a side note, this "I used a clone and.." crap is really annoying. Whether it worked or not, you're putting cost before quality control and that's piss poor ethics.

firstly not the point of the post the point is that i can not rite the ECC and the chinese and real ones work I don't care which one i use I just wanna know how I can fix this...

 

[john mathews]

wheres my security its time to put ban down

 

[Brickmii82]

firstly not the point of the post the point is that i can not rite the ECC and the chinese and real ones work I don't care which one i use I just wanna know how I can fix this...

This is a TX support forum. Not a fix my cheap @$$ pos chip forum. Get real stuff and try again.

 

[vloxter]

This is a TX support forum. Not a fix my cheap @$$ pos chip forum. Get real stuff and try again.

I have the f**king real thing but any ways here I went to go pick my iphone 6 up here are some better pics...

http://postimg.org/gallery/13ewdrz02/52e8110b/

 

[vloxter]

U still need to fill out the template with good clear pics of your soldering and genuine coolrunner.

Products:
Coolrunner Rev c
Jr programmer V2

Mobo:
Trinity

CB? not sure sorry

Jrunner log:

I was just getting bad blocks when doing it now I am getting


Version: 10
Flash Config: 0x00000000
Can not Continue

Problems:

Well it wont write ECC (was the first problem) now seems to be that and my coolrunner is both red, and green.

Thanks

Pictures

http://postimg.org/gallery/13ewdrz02/52e8110b/

 

[john mathews]

Products:
Coolrunner Rev c
Jr programmer V2

Mobo:
Trinity

CB? not sure sorry

Jrunner log:

I was just getting bad blocks when doing it now I am getting


Version: 10
Flash Config: 0x00000000
Can not Continue

Problems:

Well it wont write ECC (was the first problem) now seems to be that and my coolrunner is both red, and green.

Thanks

Pictures

http://postimg.org/gallery/13ewdrz02/52e8110b/

u need to stop and put in a request for service before u kill this xbox your soldering is horrible not trying to be mean

 

[john mathews]

I will install it for 30 dollars as long as u pay shipping

 

[vloxter]

I will install it for 30 dollars as long as u pay shipping

My friend Eric will do it for free I am learning and have done 2 by my self good but thanks

 

[john mathews]

My friend Eric will do it for free I am learning and have done 2 by my self good but thanks

well u better get ahold of him before its 2 late

 

[BrockThunderjam]

If you want some constructive criticism cut your leads shorter and get better flux. It looks like the flux you're using is not very good or you're not using flux and applying too much heat to the solder points. Could be that your tip is too small and you're having to hold it on the joint for too long to get the solder to flow. Your finished joints should have a nice clean shiny fluid round look.

It's hard to read your thread with all the bs posts in it from others, but are you still just getting the beep sound when you try powering on the console? If so you could have damaged the stdby_clk point.

Also, you should tin the pads you're soldering to on the board before you try and solder the wires to them.

 

[XDK]

My friend Eric will do it for free I am learning and have done 2 by my self good but thanks

if he lives in texas and his name is eric (houston area specifically) run like hell and dont let him touch your sh*t.. if NOT disregard this post entirely

 

[ablegepu]

you could remove the cr since you haven't made it far enough to use it yet, and just focus on writing the ecc to the console for now. have you tried reading the nand again and if you can then compare it to the original you save when you first read the nand. if you can do that then post jr log.

 

[uns97]

Writting the ECC does not require installing any chip. I don't know whether the original poster has the original nand dump(s) at all, as if reading the nand was successfull then writting should be aswell - except as some of you already said the standby_clk point got damaged during the coolrunner installation. I have no clue why he did not write the ecc AFTER reading the nand and BEFORE installing the chip itself, as that would help to say what the problem may be. Anyway looking at the soldering I would say it causes the whole trouble. Practicing to solder on a working board is not the best idea to be honest.

 

[GeekHeat]

I always get 2 matching dumps and write ecc before I start soldering the glitch chip. While I'm waiting for the nand to read, I get the wires and glitch chip prepared ready for install.