Xbox Won't turn on

[matt2416]

But How, I only programmed it once and never plugged it in again!?

 

[DayvG]

Well we'll wait for dgenx's developments. I'm sure he'll come up with something.

 

[x360ccm]

you be pleased to know i now have your xbox booting up.

now to do something i never done before.

install a cygnos.

so a bit of reading for me,then install it propper....:biggrin:

 

[matt2416]

you be pleased to know i now have your xbox booting up.

now to do something i never done before.

install a cygnos.

so a bit of reading for me,then install it propper....:biggrin:

Thankyou SO MUCH!! and Well done.

 

[matt2416]

you be pleased to know i now have your xbox booting up.

now to do something i never done before.

install a cygnos.

so a bit of reading for me,then install it propper....:biggrin:

Do you need the guide? The one on the Cygnos website is not the best.

 

[x360ccm]

tbh i never used anything other than tx gear.

i find the right one for the Cygnos i read what i find.

then i solder away.

i still cant read the nand using a nand x.and i no for sure it not my soldering.

 

[matt2416]

tbh i never used anything other than tx gear.

i find the right one for the Cygnos i read what i find.

then i solder away.

i still cant read the nand using a nand x.and i no for sure it not my soldering.

But is the Nand readable with the Cygnos USB?

 

[DayvG]

Only time will tell I would imagine. Your man needs a rest after the work he's done on the board already. Installing that Cygnos properly is the next step.

 

[x360ccm]

i not installed it yet.

i just been runnin the xbox make sure it runnin fine.befor i install the cr and cygnos.

making sure there no 0022.as you said it did that.i had no 0022 it's been on 3 hours well there abouts.

think i done well tbh lmao.to get it running.

 

[DayvG]

A wizard with an iron i'd say, you make me look bad for not fixing it

 

[DayvG]

It should be working after doing that but u may have fried it

It is working. He's just making sure no RROD before installing Cygnos and CR......as he said.

 

[x360ccm]

just a teaser matt.so you no it bootin as retail.you must no that sticky thing on the back what the cr was stuck to.

i blank bits of the id out ok.

 

[DayvG]

just a teaser matt.so you no it bootin as retail.you must no that sticky thing on the back what the cr was stuck to.

i blank bits of the id out ok.

It's looking slightly more healthy than it did on my kitchen side

You think it might be because I didn't have the fans sat on the heat sink when I tried to power it on?

 

[x360ccm]

update still bootin retail.

install the cygnos switch to that it gives me 0022 fan spins 100 mile a hour lol.but i not programed it yet.

did you progam it matt.

more readin :biggrin:

 

[matt2416]

update still bootin retail.

install the cygnos switch to that it gives me 0022 fan spins 100 mile a hour lol.but i not programed it yet.

did you progam it matt.

more readin :biggrin:

Did you attach the rest of the wires and u programmed it once yes lol.

 

[x360ccm]

rest of what wires.i ask you if you had programed it.

this is the install and how it surpose to look

 

[matt2416]

rest of what wires.i ask you if you had programed it.

this is the install and how it surpose to look

Yeah I meant to say I programmed it before and that link is dead.

Also the wires from the pads such as D1 etc

 

[x360ccm]

link not dead now.

read it.

 

[matt2416]

link not dead now.

read it.

down the bottom of the page, it has the picture with nearly all the pads wired.

 

[DayvG]

Oh, the pictures for the slim install?!?