Xbox360 pads Lifted Help

[2615863]

[Resolved] Xbox360 Lifted Pads

My customer brought me a Falcon XBox to be RGHed, but he had lifted the Stby_Clk. I used the alternate point and it booted fine. So I put how glue so it could stay. It somehow got loose so I took the glue off and it lifted the pad... I need help. Thank you

I had used the alternate point before, I just had never used hot glue...

 

[Martin C]

Send it to someone who can fix it.

 

[JohnsonMighty]

scrap the pin that is above the missing resistor, add a new resistor then add a wire to the other side and connect it to the alt point under the board. Or as martin said, send it to a pro.

 

[2615863]

Send it to someone who can fix it.

I can fix it. I just am not completely sure where to Put everything

 

[JohnsonMighty]

I can fix it. I just am not completely sure where to Put everything

look at what I said.

 

[Martin C]

I can fix it. I just am not completely sure where to Put everything

Are there not enough posts and images to show you what it should look like?

 

[2615863]

Are there not enough posts and images to show you what it should look like?

Ok whatever. Can I use a resistor from a zephr?

Edit: Like this

 

[Avinitlarge]

you still need to fit the resistor, Im sure its a 36 ohm

or is it a 34 ohm, can't remember off the top of my head

 

[2615863]

you still need to fit the resistor, Im sure its a 36 ohm

or is it a 34 ohm, can't remember off the top of my head

Thanks, Also is there a polarity, Ive placed it but xbox wont boot

 

[gargoyle67]

I stopped using hot glue for holding all the wires as it's a pain in the arse to remove, I just put a blob about an inch from the solder points on the back of the board and electric tape the rest for this very reason. I've see ppl putting on the solder points after they've soldered the wires, That's ok until you have to remove them for say the new POST QSB, Then you risk pulling something off unless your ultra careful with a hair dryer.

 

[josh1095]

thats easier than the one i fixed on a slim. its not that hard. just put something similiar in resistance there and ur good to go. i used a 50 ohm instead of 33. didnt matter at all. not sure if the slim and falcon differ in that respect

 

[2615863]

thats easier than the one i fixed on a slim. its not that hard. just put something similiar in resistance there and ur good to go. i used a 50 ohm instead of 33. didnt matter at all. not sure if the slim and falcon differ in that respect

Yea The guy aslo brought me a jasper and i put a resistor on and it worked. this one wont work ...

I know you can barely see it, but I oulled a resisotr from my zpeher and put it on here and connected it with botht the alternate points to try it out and no luck.. Please help...

EDIT: The console boots, but only when the coolrunner isnt connceted to the 3v3

 

[Avinitlarge]

Did you connect it up like in the pic?

 

[2615863]

Did you connect it up like in the pic?

No I just bridged the Point where I had the resistor to the Alternate point on the bottom. No resistor just a wire.
Booted Xell up fine.

My original problem was the 3volts. Pluggged in the wrong spot. That made me f**k up the rest lol. I got it fixed though

 

[2615863]

WTF!!! I just put it back in the cage carefully and it will only turn on for a split second

 

[2615863]

OK I finally got it working. Now it gives me 2 red lights after like 5 seconds of being on... I tried replacing the Thermal Paste under the GPU, and I tightened the clamps

 

[2615863]

Never Mind I got everything sorted out. Fixing it was easy, what messed me up was the 3volt red wire

Please Close/Delete this thread please