RGH Xell Doesnt boot - Remap the bad block?

H

haterain

Junior Member
Sep 1, 2011
12
0
I have trinity board that I am trying glitch.
I have made several dumps of my nand and every single nand shows bad block at 0x00ED [Offset: 0x003D1A00]. J-runner verifies my dumps as match.

It is sounds like it is trying to glitch (reseting) but without success. So I ask do I need to remap this bad block in order to boot xell properly?

This is my second slim that i am trying to glitch.
First one didnt cause any trouble but it didnt have any bad blocks either.

This is also CB 9230.
I tried to make ecc image with both J-Runner and 360 Multibuilder.

Thanks already in advance.
 
C

Coleman

VIP Member
Oct 25, 2005
989
68
Ontario, Canada
www.colemansmodandrepair.com
I don't doubt you BL4K3Y. I just went by this.

Codenamed RGH 2.0, new features introduced:

  • Hack now works on new CB's (14717/14719 update)
  • Hack now works with all Refurbished Split CB's (4577, 5772, 6752)
  • - Zephyr CB 4577, 4575
  • - Falcon/Opus CB 5772, 5773
  • - Jasper CB 6752, 6753
  • - Trinity (Slim) CB 9230
 
jsinger47

jsinger47

Troll Eating Dogs
Feb 6, 2011
8,133
128
Grand Rapids, MI
Coleman said:
I don't doubt you BL4K3Y. I just went by this.

Codenamed RGH 2.0, new features introduced:

  • Hack now works on new CB's (14717/14719 update)
  • Hack now works with all Refurbished Split CB's (4577, 5772, 6752)
  • - Zephyr CB 4577, 4575
  • - Falcon/Opus CB 5772, 5773
  • - Jasper CB 6752, 6753
  • - Trinity (Slim) CB 9230
Click to expand...
Sure rgh2 will support 9230, but so does rgh1!
 
P

pudinkk

Senior Member
Dec 26, 2011
141
0
haterain said:
I have trinity board that I am trying glitch.
I have made several dumps of my nand and every single nand shows bad block at 0x00ED [Offset: 0x003D1A00]. J-runner verifies my dumps as match.

It is sounds like it is trying to glitch (reseting) but without success. So I ask do I need to remap this bad block in order to boot xell properly?

This is my second slim that i am trying to glitch.
First one didnt cause any trouble but it didnt have any bad blocks either.

This is also CB 9230.
I tried to make ecc image with both J-Runner and 360 Multibuilder.

Thanks already in advance.
Click to expand...
had the same problem a few days ago,after creating and writing the glitched nand back to the xbox the constant red was there and green was blinking(is is the same with you,you should see green blinking,and the fan speed goes up and down),at this point you need to check your blue wire(dont remember which point it goes to)anyways the LONG wire which goes to the back of the board.Check that if it is too tight just loosen it,and tuck it under the xclamp in loose position.that was a quick fix to my issue I hope it also works for you.

if that doesnt work you can try checking for continuity on stby-clk point just below hana chip.and other connections(if someone could give me a tutorial on that would be great by the way,still have no idea how I can use this multimeter)

if that still doesnt help you may check on your nand dump's bad blocks.
 
You must log in or register to reply here.