RGH Xell freezing rawflash

Status
Not open for further replies.
A

ando2k9

VIP Member
Jul 5, 2010
185
0
Just getting round to doing a family members elite jasper dumped the nand got the key xell boots etc

made my nandflash copied it to a usb stick along with xenon.elf it sees the stick and sees xenon.elf but gets no further

all i get is "executing....." then nothing sometimes it'll freeze at controller 0

anyone any ideas?

tried a few usb sticks fat32 and fat still the same at a loss at the moment, not wanting to flash the nand via pc as i'm on lpt at the moment.
 
A

ando2k9

VIP Member
Jul 5, 2010
185
0
blakey8 said:
How did you build your image?

Does the file size look good (16MB/64MB)?

Open the NAND in 360 Flash Tool and see if everything looks good.
Click to expand...
it doesn't even get to the point where the screen switches to load rawflash

will check nand though
 
A

ando2k9

VIP Member
Jul 5, 2010
185
0
nand opens fine no bad blocks key is fine too

one thing i did notice (not sure if it's anything not to well up on it) is that the 6bl and 7bl are both blank whereas another image i have from a falcon has info in those boxes

also again not sure if this makes any difference it was running a old dash a 8469 i think didn't update it just dumped the nand and went from there
 
manwithoutname

manwithoutname

1
Jun 4, 2010
3,080
0
I'm assuming it freezes with or without a USB stick inserted?

---------- Post added at 12:09 ---------- Previous post was at 12:08 ----------
ando2k9 said:
nand opens fine no bad blocks key is fine too

one thing i did notice (not sure if it's anything not to well up on it) is that the 6bl and 7bl are both blank whereas another image i have from a falcon has info in those boxes

also again not sure if this makes any difference it was running a old dash a 8469 i think didn't update it just dumped the nand and went from there
Click to expand...
The no info is normal for BB Jaspers ...
 
A

ando2k9

VIP Member
Jul 5, 2010
185
0
manwithoutname said:
I'm assuming it freezes with or without a USB stick inserted?

---------- Post added at 12:09 ---------- Previous post was at 12:08 ----------



The no info is normal for BB Jaspers ...
Click to expand...
strangely now you've mentioned it a few occasions it would refuse to glitch with a usb stick attatched as soon as i remove it it glitches thats only happened a few times though

also not a BB jasper just a 16mb
 
manwithoutname

manwithoutname

1
Jun 4, 2010
3,080
0
I would recheck the wiring layout as I suspect some interference.
 
  • Like
Reactions: ando2k9
A

ando2k9

VIP Member
Jul 5, 2010
185
0
still the same, gonna flash the first 40 blocks of the created nand image see if that xell is any better
 
A

ando2k9

VIP Member
Jul 5, 2010
185
0
not the only issue, flashed full nand now the coolrunner glitches first time within 2 seconds but nothing on screen and RF board doesn't do its usual ROL just blinks and no red lights, pressing eject and booting to xell boots first time

at a loss on what to do
 
A

ando2k9

VIP Member
Jul 5, 2010
185
0
from reading that thread wrong ldv would result in red lights i never get any, my fuseset only has 2 f's though not sure thats right but i've no clue just going from that thread

same issue but not a frankenstein xbox nor is it a BB http://team-xecuter.com/forums/showpost.php?p=530463&postcount=71

also used multi_builder 0.7 to build the image

reran multi builder at the end screen showing your created image my CF LDV is 2 so it is correct
 
Last edited:
Status
Not open for further replies.