Xell will not boot

[briggs01]

excuse me I was just telling him there is a option if hes selecting glitch2 for cr4

but he shouldn't select that if he is doing r-jtag

 

[Antalpromille]

excuse me I was just telling him there is a option if hes selecting glitch2 for cr4

Yeah but if you read his logs wich is the only information we where given you would have noticed he selected R-jtag, so your help was not much better.

 

[briggs01]

sorry cocoloco420 I have had a few lagers lol wasn't concentrating , so as stated mate you need to post pics

 

[john mathews]

be gone op has been instructed what to do and post pics of install and to try differnet dips/ theres nothing hard about installing a cr4 in any xbox falcon jasper zephyr and slims ive done them all even got a zephyr to glitch with it op all the info is in the cr4 stickys its very simple and theres some good people on here to help not everyone on here are rude:wink:

 

[briggs01]

be gone op has been instructed what to do and post pics of install and to try differnet dips

did he mean you antalpromille or me lol

 

[Antalpromille]

did he mean you antalpromille or me lol

I don't know, but lucky OP that John the saviour is here to save the day

 

[briggs01]

I don't know, but lucky OP that John the saviour is here to save the day

lmfao ye I bow to john

 

[cocoloco420]

http://imgur.com/a/O6JAp#hGTZ6AB

here are the images guys flux all over the place but it is what it is, any help will be great.

 

[skillet34]

Looks like you have the switch set to slim in the pic. I would use the aud_clamp method as well.

 

[cocoloco420]

lol you are very helpful but I saw that the cr4 checkbox was in the rgh2 option and not in the rjtag, and kindve figured these guys or girls didn't fully read my post anyway thanks for the help!!!

 

[Joo C]

I discovered an issue which may or may not be related to this post. Did a corona v6 and after I wrote xell the cr blinked very fast with each pulse-I manually loaded the ECC and then only did the cr respond normally and boot Xell. Like I say I dont know if it's a similar situation but based on fast pulse its plausible...

 

[john mathews]

lol you are very helpful but I saw that the cr4 checkbox was in the rgh2 option and not in the rjtag, and kindve figured these guys or girls didn't fully read my post anyway thanks for the help!!!

do this bud and go to jrunner and select j-tag and audio clamp and r-jtag and create ecc and write then bridge 1/3 on jtag alt qsb and run green wire to audio clamp like in the pic

 

[cocoloco420]

I think I will use the aud_clamp, too bad the cr4 doesn't come with the extra wire. Yes in the pic the switch is set to slim but I assure you this only happened while taking the pictures as when xell was not booting I check this switch and it was set to phat.

 

[john mathews]

I think I will use the aud_clamp, too bad the cr4 doesn't come with the extra wire. Yes in the pic the switch is set to slim but I assure you this only happened while taking the pictures as when xell was not booting I check this switch and it was set to phat.

look at your jtag qsb on the bottom yours doesn't look like the pic I uploaded read what I posted to do it is so simple:rolleyes2:

 

[cocoloco420]

Thanks for the help man btw does it look like it could be something with the soldering???

 

[Taijigamer2]

I think I will use the aud_clamp, too bad the cr4 doesn't come with the extra wire. Yes in the pic the switch is set to slim but I assure you this only happened while taking the pictures as when xell was not booting I check this switch and it was set to phat.

Kynar wire is fine to use. U will probably find some spare wire in your cr4 kit once u chop down the wires for install.

 

[briggs01]

I discovered an issue which may or may not be related to this post. Did a corona v6 and after I wrote xell the cr blinked very fast with each pulse-I manually loaded the ECC and then only did the cr respond normally and boot Xell. Like I say I dont know if it's a similar situation but based on fast pulse its plausible...

yes I have had that aswell budy

 

[briggs01]

do this bud and go to jrunner and select j-tag and audio clamp and r-jtag and create ecc and write then bridge 1/3 on jtag alt qsb and run green wire to audio clamp like in the pic

after seeing his pics I can see why he may have been having problems and he could have got tis sorted long time ago , 1 he had cr4 set to slim and 2 9 times out of ten people use jtag with Aud-clamp option , also I cant zoom in very close but it looks like your qsb is soldered to the wrong place it should be on R4B24 it looks like it is to the side of if on R4B6 I could be wrong can someone verify that

 

[Antalpromille]

after seeing his pics I can see why he may have been having problems and he could have got tis sorted long time ago , 1 he had cr4 set to slim and 2 9 times out of ten people use jtag with Aud-clamp option , also I cant zoom in very close but it looks like your qsb is soldered to the wrong place it should be on R4B24 it looks like it is to the side of if on R4B6 I could be wrong can someone verify that

Look like you're right about the QSB being on the wrong point, funny how John the saviour who's always right didn't spot that

 

[lonix]

after seeing his pics I can see why he may have been having problems and he could have got tis sorted long time ago , 1 he had cr4 set to slim and 2 9 times out of ten people use jtag with Aud-clamp option , also I cant zoom in very close but it looks like your qsb is soldered to the wrong place it should be on R4B24 it looks like it is to the side of if on R4B6 I could be wrong can someone verify that

Yes definitely on the wrong point.