Xilinx Device ..... [NOT DETECTED]

ivision · May 8, 2015

Hello,

I tried glitching my xbox (Jasper 16MB) today, I wanted to use R-JTAG but I don't think the Dutch Reseller has all the parts for it so I tried RGH2. Although I'm not sure if I have the correct parts either with this, anyway I used:
- JR Programmer
- CR4 XL
- Phat QSB V2

I also have a nand-x update cable but to be honest I'm not sure what to do with it since it doesn't plug in anywhere.. I installed the drivers correctly and Windows does detect the device as it should.

J-Runner reads the nand correctly twice but when I click 'Program CoolRunner' -> 'Program CR'

Comparing...Nands are the same
Glitch Selected
Programming Coolrunner
C:\Users\joel\Downloads\J-Runner v3 (5) Core Pack\J-Runner v3 (5) Core Pack\common\xsvf\jasper.xsvf
USB XSVF Player Initialized
Xilinx Device ..... [NOT DETECTED]

I do have a multimeter so if necessary I can test some points, I tried some of myself and I noticed that the ground of the J2B1 V2 is not connected, I could just solder a wire to it but I'm not sure if I should do that..

Installation:

I tried following this guide: http://team-xecuter.com/forums/show...PHAT-Opus-Falcon-Jasper-Install-Guide-(RGH2-)
I believe his qsb is version 3 but the Dutch Reseller doesn't have it for the phat, or should I just buy one for the Trinity/Corona?

Full log:

Code:

===================================================vrijdag 8 mei 2015 20:16:55


J-Runner v0.3 Beta (7) Started




WARNING! - Your selected working directory already contains files!
You can view these files by using 'Show Working Folder' Button




Checking Files
Finished Checking Files
Checking Console..
Version: 10
Flash Config: 0x00023010
00023010
Trinity, Jasper 16MB
CB Version: 6754
Jasper 16MB
Glitch Selected
Programming Coolrunner
C:\Users\joel\Downloads\J-Runner v3 (5) Core Pack\J-Runner v3 (5) Core Pack\common\xsvf\jasper.xsvf
USB XSVF Player Initialized
Xilinx Device ..... [NOT DETECTED]
Programming Coolrunner
C:\Users\joel\Downloads\J-Runner v3 (5) Core Pack\J-Runner v3 (5) Core Pack\common\xsvf\jasper.xsvf
USB XSVF Player Initialized
Xilinx Device ..... [NOT DETECTED]
Checking Console..
Version: 10
Flash Config: 0x00023010
00023010
Trinity, Jasper 16MB
CB Version: 6754
Jasper 16MB
Programming Coolrunner
C:\Users\joel\Downloads\J-Runner v3 (5) Core Pack\J-Runner v3 (5) Core Pack\common\xsvf\jasper.xsvf
USB XSVF Player Initialized
Xilinx Device ..... [NOT DETECTED]
Jtag Selected
Aud_Clamp Selected
Aud_Clamp de-Selected
R-Jtag Selected
Programming Coolrunner
C:\Users\joel\Downloads\J-Runner v3 (5) Core Pack\J-Runner v3 (5) Core Pack\common\xsvf\jasper.xsvf
Device not found.
R-Jtag de-Selected
Glitch Selected
Programming Coolrunner
C:\Users\joel\Downloads\J-Runner v3 (5) Core Pack\J-Runner v3 (5) Core Pack\common\xsvf\jasper.xsvf
Device not found.
Programming Coolrunner
C:\Users\joel\Downloads\J-Runner v3 (5) Core Pack\J-Runner v3 (5) Core Pack\common\xsvf\jasper.xsvf
Device not found.
Programming Coolrunner
C:\Users\joel\Downloads\J-Runner v3 (5) Core Pack\J-Runner v3 (5) Core Pack\common\xsvf\jasper.xsvf
USB XSVF Player Initialized
Xilinx Device ..... [NOT DETECTED]
Programming Coolrunner
C:\Users\joel\Downloads\J-Runner v3 (5) Core Pack\J-Runner v3 (5) Core Pack\common\xsvf\jasper.xsvf
USB XSVF Player Initialized
Xilinx Device ..... [NOT DETECTED]
Programming Coolrunner
C:\Users\joel\Downloads\J-Runner v3 (5) Core Pack\J-Runner v3 (5) Core Pack\common\xsvf\jasper.xsvf
USB XSVF Player Initialized
Xilinx Device ..... [NOT DETECTED]
Programming Coolrunner
C:\Users\joel\Downloads\J-Runner v3 (5) Core Pack\J-Runner v3 (5) Core Pack\common\xsvf\jasper.xsvf
USB XSVF Player Initialized
Xilinx Device ..... [NOT DETECTED]
Version: 10
Flash Config: 0x00023010
00023010
Trinity, Jasper 16MB
CB Version: 6754
Jasper 16MB
Reading Nand to C:\Users\joel\Downloads\J-Runner v3 (5) Core Pack\J-Runner v3 (5) Core Pack\output\nanddump1.bin
Cancelled
Version: 10
Flash Config: 0x00023010
00023010
Trinity, Jasper 16MB
CB Version: 6754
Jasper 16MB
Reading Nand to C:\Users\joel\Downloads\J-Runner v3 (5) Core Pack\J-Runner v3 (5) Core Pack\output\nanddump1.bin
Reading Nand
Done!
in 3:25 min:sec


Reading Nand to C:\Users\joel\Downloads\J-Runner v3 (5) Core Pack\J-Runner v3 (5) Core Pack\output\nanddump2.bin
Initializing nanddump1.bin..
Jasper 16MB
Jtag Selected
Nand Initialization Finished
Reading Nand
Done!
in 3:25 min:sec


Comparing...
Nands are the same
Glitch Selected
Programming Coolrunner
C:\Users\joel\Downloads\J-Runner v3 (5) Core Pack\J-Runner v3 (5) Core Pack\common\xsvf\jasper.xsvf
USB XSVF Player Initialized
Xilinx Device ..... [NOT DETECTED]

nofeloniesyet · May 8, 2015

you dont program a cr4 buddy,it comes already done.

scott1503 · May 8, 2015

you do not need to program a cr4 they come pre programed from factory. it says nothing about attepting to program the chip in the guide

keil423 · May 8, 2015

You never write anything to the cr4. You better hope it failed because if it erased it your cr4 is now a paper weight.

ivision · May 8, 2015

Oh.. I feel stupid now haha, but why is it in the userguide of JRunner? Or did I misread what I shouldn't be doing?
What would be the next step then, Create ECC?

keil423 · May 8, 2015

You have your cr4 on 3v3 where as it needs 5v

ivision · May 8, 2015

keil423 said:
You have your cr4 on 3v3 where as it needs 5v

I see, but which should I use for 5V? I wired exactly as the guide I listed in the OT.

GeekHeat · May 8, 2015

ivision said:
I see, but which should I use for 5V? I wired exactly as the guide I listed in the OT.

The red dot in the PIC is 5v point.

ivision · May 8, 2015

Okay so I resoldered the wire but now JRunner is unable to read the nand memory? Actually it does read it but it detects the board as Trinity:

Version: 10Flash Config: 0x00023010
00023010
Trinity, Jasper 16MB
CB Version: 9188
Trinity
Reading Nand to C:\Users\joel\Downloads\J-Runner v3 (5) Core Pack\J-Runner v3 (5) Core Pack\output\nanddump1.bin
Reading Nand
Done!
in 3:28 min:sec

Reading Nand to C:\Users\joel\Downloads\J-Runner v3 (5) Core Pack\J-Runner v3 (5) Core Pack\output\nanddump2.bin
Initializing nanddump1.bin..
Header is wrong..
Trinity
Glitch2 Selected
Nand Initialization Finished
Reading Nand
Done!
in 3:26 min:sec

Comparing...
Nands are the same

At first it didn't read the nand at all but pressing the reset button on the programmer fixed that but now it is unable to read it correctely I guess?

nofeloniesyet · May 8, 2015

ivision said:
Okay so I resoldered the wire but now JRunner is unable to read the nand memory? Actually it does read it but it detects the board as Trinity:

At first it didn't read the nand at all but pressing the reset button on the programmer fixed that but now it is unable to read it correctely I guess?

if you have written the ecc already it will show as trinity.

ablegepu · May 8, 2015

it is fine the nands matched now copy and save your nands somewhere they will be safe.
you are good to go just create ecc and write it.

ivision · May 10, 2015

Okay what should I do now? I'm got a bit confused, I have the idea that the userguide is outdated or something. At least it tells me things I shouldn't be doing.. What I did was clicking Create ECC and then Write ECC. However when I turn the xbox on and connect it with the TV it doens't show anything. I hoped I see the Xell Reloaded screen but that is not the case.

The CR does blink green every 5 seconds, not sure if that means something?

ablegepu · May 10, 2015

did you resolder the red wire from the cr4 to the 5v pad like suggested?
Do you have a red light on constantly on the cr4?
And do you have the green light flash every 5 seconds on the cr4?

If not you need to post new pictures of your install please. also please post your full Jrunner log from the jrunner folder.

ablegepu · May 10, 2015

Oh I guess none of us noticed earlier but your post wire is on the wrong pad, it goes to ft6u1.

scratch that.. Thought you were using Rjtag method. The wire is correct.:facepalm:

ivision · May 10, 2015

Yes I do have all what you said so the install is exactly the same except the red wire solder point. I measured its voltage and it is indeed the 5V point. Log file comming up in a sec..

ivision · May 10, 2015

ablegepu said:
Oh I guess none of us noticed earlier but your post wire is on the wrong pad, it goes to ft6u1.

Ahaa.. And which one is the post (color)? Couldn't find it anywhere, I'll resolder it. In the mean time here is the log (I did mess around a bit with the settings etc as you'll see in the log

) : http://pastebin.com/FshF1jhF

Today:

Code:

===================================================
zondag 10 mei 2015 10:04:10


J-Runner v0.3 Beta (7) Started




It's advised to run in administrator mode on Windows 8
WARNING! - Your selected working directory already contains files!
You can view these files by using 'Show Working Folder' Button






===================================================
zondag 10 mei 2015 10:04:19


J-Runner v0.3 Beta (7) Started




WARNING! - Your selected working directory already contains files!
You can view these files by using 'Show Working Folder' Button




Checking Files
Finished Checking Files
Initializing nanddump1.bin..
Header is wrong..
Trinity
Glitch2 Selected
Nand Initialization Finished
Header is wrong..
Invalid Image
Failed to create ecc image
Header is wrong..
Invalid Image
Failed to create ecc image
You need an .ecc image
Comparing...
Nands are the same
Header is wrong..
Invalid Image
Failed to create ecc image
Initializing nanddump1.bin..
Header is wrong..
Trinity
Nand Initialization Finished
Header is wrong..
Invalid Image
Failed to create ecc image
Version: 10
Flash Config: 0x00023010
00023010
Trinity, Jasper 16MB
CB Version: 9188
Trinity
Reading Nand to C:\Users\joel\Downloads\J-Runner v3 (5) Core Pack\J-Runner v3 (5) Core Pack\output\nanddump1.bin
Reading Nand
Done!
in 2:23 min:sec


Reading Nand to C:\Users\joel\Downloads\J-Runner v3 (5) Core Pack\J-Runner v3 (5) Core Pack\output\nanddump2.bin
Initializing nanddump1.bin..
Header is wrong..
Trinity
Nand Initialization Finished
Reading Nand
Done!
in 0:02 min:sec


Comparing...
Initializing nanddump1.bin..
Jasper 16MB
Jtag Selected
Nand Initialization Finished
Comparing...
Nands are the same

Edit: aha okay, I'll leave it then

ablegepu · May 10, 2015

That log is just from today. so it doesn't show everything you have done when reading/writing to the nand. As far as I can tell though you have wrong header which means the nand you are reading is actually an ecc that you flashed earlier on. You need to find your original nanddump.bin that you read off of the xbox the first time. If you left it in the working folder and you did not save it and then you made an ecc, flashed it to the console and then read the nand again, Then you probably overwrote the original nanddumps. I need the full Jrunner log. log.txt if you have it

ivision · May 10, 2015

The pastebin links to the older log file it had to much characters for the post.
I do have the old nandbins, I deleted the output directory couple times so I have them in my bin.

ablegepu · May 10, 2015

Do you have the recommended dip switches turned on

- - - Updated - - -

ivision said:
The pastebin links to the older log file it had to much characters for the post.

ok thanks

ivision · May 10, 2015

ablegepu said:
Do you have the recommended dip switches turned on

- - - Updated - - -

ok thanks

Yes I do have that, sorry didn't notice it was unable to see it from the pictures. Admittedly they all are kind a bad quality.

Search

Search

Xilinx Device ..... [NOT DETECTED]

ivision

Full Member

nofeloniesyet

scott1503

keil423

ivision

Full Member

keil423

ivision

Full Member

GeekHeat

ivision

Full Member

nofeloniesyet

ablegepu

ivision

Full Member

ablegepu

ablegepu

ivision

Full Member

ivision

Full Member

ablegepu

ivision

Full Member

ablegepu

ivision

Full Member